Zhejiang Longchi Technology Co., Ltd.

0086-572-2596377 sales@best-solar-panels.com

60A PWM controller with LCD display

Output Current:60A
Input voltage:24V/36V/48V
Color box packing
0.69Kg/PCS,30PCS/CTN
Carton size:41*36*43cm
0.063m³/ctn

  • PRODUCT DETAIL

:Stop supply power to the load condition
:Closed to the battery
:Supply power to the load, load circuit without current
:Battery charging at full speed
:Load circuit current
:Float charging battery pool
:Load identification
:System working properly
:Solar panel identification
:System working abnormal
:Load light-operate identification
:Battery power indicator
:Load time control identification
:Battery identification
Keys function description
: Interface cycle switch button, use the buttons can be in various aspects between switching,circulation sequence is shown in figure 1
:Parameter adjustment increase buttons.In addition, in the condition of parameter to see long press this button more than 5 seconds, the parameters restore to factory Settings.
:Parameter adjustment reduce buttons.In addition,press this button can open load and close load in the main interface.


Parameter checking and Settings
Controller right after power on default into the storage battery voltage display interface, this interface is the main interface of controller .Using the buttons can browse the following parameters of the interface in turn.If change the interface parameters can be set up, can long press button (> 5 seconds, Numbers start flashing) enter the parameter Settings interface, set up after the long press the button to exit the parameter Settings interface, digital stop flashing.
Viewing the battery voltage
As shown in the picture on the right, according to the numerical value for the current battery voltage.
This main interface, show charging status, discharge, battery power, storage battery voltage.


Load on and off control
In battery voltage to see interface, can use this button to open and close load.,
In the other screen key without this feature.
Environment temperature check
As showing in the figure below,it shows the values for ambient temperature controller, used for battery charging pressure
Temperature compensation.it is necessary to install the temperature sensor during working.


Solar panel generate electricity current viewing
As shown in the figure below, shows the values for solar panel generate electricity current.


Load current view
As shown in the figure below, the display value of load electric current.


Solar panels accumulated generating hours check and reset
As shown in the figure below, shows the values for solar panels accumulated generating in hours.
In this interface press button long(> 5 seconds), will lose the cumulative generating hours.


Load the cumulative dischargeAnn hours check and reset
As shown in the figure below, shows that the numerical to load the total electricity in hours.
In this interface press button long (> 5 seconds), will lose the cumulative powerAnn hours.


Under-voltage protection voltage check and Settings
As shown in the figure below, shows the values for low voltage protection voltage.When the battery voltage is lower than the low voltage protection electric.Pressure controller will disconnect the load circuit, to prevent the battery by excessive discharge.
In this interface press button long (> 5 seconds), digital start flashing, says it has into the under-voltage protection voltage.Settings interface, can be used, the key to adjust the parameters.
Set up the interface, can use these keys to adjust the parameters.
Set up after the press the button long (> 5 seconds) exit parameter Settings interface, the setting of the controller will protect.


Under-voltage and recover-voltage viewing and setting
As shown in the figure below, shows the values for owe voltage recovery voltage.After the controller under voltage protection, storage battery
Electricity back to the higher than under voltage recovery voltage, the controller will return through to load circuit.
In this interface press button long (> 5 seconds), digital start flashing, said has entered owe pressure recovery voltage
Settings interface, can be using key to adjust the parameters.
Set up after the press this button long (> 5 seconds) exit parameter Settings interface, the setting of the controller will protect.


Stop charging pressure check and Settings
As shown in the figure below, shows the values for stop charging pressure.When the battery voltage to stop charging pressure control。Controller will disconnect the charging circuit, prevent battery charged by excessive, will be after the battery voltage drops。A new charging circuit is connected.
In this interface press button long (> 5 seconds), digital start flashing, said has entered stop charging pressure.
Settings interface, can be using key to adjust the parameters.
Set up after the press this button long (> 5 seconds) exit parameter Settings interface, the setting of the controller will protect.


Checking and setting the load patterns
As shown in the figure below to load mode to view interface, different value represents the different load patterns.
24 h – indicate normal mode, remain the state of power supply load in trouble-free situation.
1h-23h ~ indicate light-operated delay model, the load in power supply and delay set hours after dark,The number of closed after load.
0 h – indicate light-operated model, load after dark start power supply, the morning after closed load.
Long press button in this interface (> 5 seconds), digital start flashing, says it has into the
load mode setting interface,can be using these keys to adjust the parameters.
Long press button in the interface (> 5 seconds), digital start flashing, says it has into the load mode setting interface

Inquiry